Radioactive decay source, practical example
The radioactive decay source mode was implemented in Serpent 2.1.24 for the purpose of radiation transport calculations involving activated materials. The source term is determined by:
- Isotopic material compositions, either user-defined or obtained from a previous burnup / activation calculation
- Decay constants of radioactive nuclides read from ENDF format decay data file
- Emission spectra read from ENDF format decay data file
The radiation types in version 2.1.28 and earlier are limited to discrete photon emitting reactions. Work on continuum reactions, neutron emission and bremsstrahlung from beta decay is under way.
The radioactive decay source mode is most conveniently used with burnup or activation calculation, in which case the radioactive material compositions can be read from a binary restart file (see the set rfw and set rfr options). In such case the same input can be used for both calculations without major modifications. Serpent converts the isotopic material compositions in the neutron transport calculation into elemental compositions for the following photon transport calculation, and source rate normalization is carried out automatically based on the total emission rate.
There are two sampling modes for selecting the position of emitted particles:
- Analog sampling mode -- Source points are sampled uniformly throughout the geometry and each point accepted or rejected based on the ratio of local to maximum emission rate
- Implicit sampling mode -- Source points are sampled uniformly throughout the geometry and the weight of the emitted photon adjusted according to the ratio of local to average emission rate.
Efficiency of analog sampling may become poor when most (but not all) of the activity is concentrated on local hot spots. Implicit sampling allows covering the geometry uniformly with source points, but may lead to sparse distribution of weights and lead to problems with tally statistics.
The radioactive decay source mode has been tested in radiation shielding calculations involving a transport cask containing irradiated fuel and shut-down dose rate calculations for the ITER fusion reactor.
Production of decay source from burnup calculation
% --- Pin-cell burnup calculation ---------------------------- set title "Pin-cell burnup calculation" % --- Pin definition: pin 1 fuel 0.412 clad 0.475 water % --- Geometry: surf 1 sqc 0.0 0.0 0.665 cell 1 0 fill 1 -1 cell 2 0 outside 1 % --- Periodic boundary condition: set bc 3 % --- Fuel (composition given in atomic densities): mat fuel -10.045 burn 1 92234.09c 6.15169E+18 92235.09c 6.89220E+20 92236.09c 3.16265E+18 92238.09c 2.17103E+22 6012.09c 9.13357E+18 7014.09c 1.04072E+19 8016.09c 4.48178E+22 % --- Zircalloy cladding: mat clad -6.560 40000.06c -0.9791 50000.06c -0.0159 26000.06c -0.0050 % --- Water (composition given in atomic densities): mat water -0.7569 moder lwtr 1001 1001.06c 5.06153E+22 8016.06c 2.53076E+22 5010.06c 2.75612E+18 5011.06c 1.11890E+19 % --- Thermal scattering data for light water: therm lwtr lwj3.11t % --- Data libraries: set acelib "/xs/sss_jeff31u.xsdata" set declib "/xs/sss_jeff31.dec" set nfylib "/xs/sss_jeff31.nfy" % --- Options: set gcu -1 set pop 2000 500 20 % --- Write binary restart file: set rfw 1 % --- Burnup calculation: set powdens 40.0E-3 dep butot 0.1 0.5 1 5 10 15 20 25 30 35 40 % ------------------------------------------------------------
Photon transport simulation using radioactive decay source
- ^ Sirén, P. and Leppänen, J. "Expanding the Use of Serpent 2 to Fusion Applications: Development of a Plasma Neutron Source." In proc. PHYSOR 2016. Sun Valley, ID, May 1-6, 2016.
- ^ Leppänen, J. and Kaltiaisenaho, T. "Expanding the Use of Serpent 2 to Fusion Applications: Shut-down Dose Rate Calculations." In proc. PHYSOR 2016. Sun Valley, ID, May 1-6, 2016.