# Difference between revisions of "Automated depletion zone division"

(→Radial, angular and axial sub-division) |
(→Sub-division and geometry levels) |
||

Line 81: | Line 81: | ||

Consider another example, consisting of 4 HTGR fuel pebbles, each filled with 50 TRISO particles. The geometry consits of 5 levels: | Consider another example, consisting of 4 HTGR fuel pebbles, each filled with 50 TRISO particles. The geometry consits of 5 levels: | ||

− | #Cube containing the pebbles | + | #Cube containing the pebbles, and the outside world |

#Pebble distribution | #Pebble distribution | ||

#Pebble universes | #Pebble universes |

## Revision as of 14:32, 27 November 2015

Serpent 2 has the capability to perform automated depletion zone division for materials in burnup calculation. There are two options:

- The number of radial regions in 2D pin-type objects can be entered directly in the material card ("Serpent 1" type division).
- The div card can be used to perform 3D depletion zone division.

Both approaches are discussed below. With automated depletion zone division it is important to always check the volumes using the Monte Carlo based volume checker routine, and if necessary, define the volumes manually.

## Contents

## Division with material card

See Sec. 8.2 in Serpent 1 input manual.^{[1]}

## Division with divisor card

The div card can be used to separate each cell into its own depletion zone, and further sub-divide pin-type objects into axial-, radial and angular sub-zones. The division takes into account the universe-based geometry structure, so same cells in two different universes are treated separately. For fuel assembly geometries, for example, each pin can be treated as a separate material. If the assembly is put in a core lattice, the same pin in two different assembly positions can be treated separately and so on.

The basic methodology is best illustrated by an example involving a BWR fuel assembly geometry consisting of a 10 x 10 lattice of fuel pins with 13 different fuel types (fuel1, fuel2, ... fuel13). The different materials are plotted in different colors:

### Simple cell-based division

Defining a div-card for each fuel composition:

div fuel1 sep 1 div fuel2 sep 1 ... div fuel13 sep 1

divides identical compositions into different depletion zones:

Some of the colors in the plot may appear similar, but each regions now contains a different material. The value after the sep-entry defines the geometry level at which the division is performed. Value 1 refers to the last level, which essentially means that all cells in the geometry are handled separately. The use of the sep entry is revisited at the end of this example.

### Radial, angular and axial sub-division

Accounting for the depletion of burnable absorber requires radial sub-division, which for pin-type material regions can be done automatically. If it is assumed that the absorber is mixed in fuel types 9-13, sub-division into 10 rings can be done using the subr-entry:

div fuel9 sep 1 subr 10 0.0 4.38E-01 div fuel10 sep 1 subr 10 0.0 4.38E-01 div fuel11 sep 1 subr 10 0.0 4.38E-01 div fuel12 sep 1 subr 10 0.0 4.38E-01 div fuel13 sep 1 subr 10 0.0 4.38E-01

The division is made between 0 and 0.438 cm into 10 rings with equal cross-sectional area:

If necessary, the fuel pins can be further sub-divided into angular sectors using the subs-entry, for example:

div fuel1 sep 1 subs 4 45.0 div fuel2 sep 1 subs 4 45.0 ... div fuel13 sep 1 subr 10 0.0 4.38E-01 subs 4 45.0

The pins are divided into 4 sectors and tilted by 45 degrees:

The axial division works in a similar manner using the subz-entry, taking the number of axial zones and minimum and maximum coordinate as the input values. Radial, angular and axial sub-division are limited to pin-type material regions, but the cell-based division applies to any type of geometry.

### Sub-division and geometry levels

In large complex geometries it may not be possible to handle every cell as a separate depletion zone. In such case the sep-entry can be used, for example, to sub-divide the fuel in a large LWR core into separate depletion zones on assembly-, instead of pin-basis. Another example is an HGTR geometry consisting of millions of individual fuel kernels. Instead of handling each kernel as a separate depletion zone, the division can be done based on compacts or pebbles.

The concept of a geometry level may be a bit difficult to understand, but basically it means that whenever there is a cell, lattice, or any other geometry structure filled with another universe, it adds a new level in the geometry. What makes things a bit more complicated is that regular structures, such as lattices, also form a new level. So in a typlical BWR assembly geometry, for example, the levels would be:

- Structures defining channel box wall, moderator channels, etc. and the outside world
- Lattice of fuel pins
- pin universes

The number "<lvl>" following the "sep" entry determines the number of levels counted __backwards__ from the last one (<lvl> = 1 being the last).

Consider another example, consisting of 4 HTGR fuel pebbles, each filled with 50 TRISO particles. The geometry consits of 5 levels:

- Cube containing the pebbles, and the outside world
- Pebble distribution
- Pebble universes
- Particle distributions
- Particle universes

With

div sep 1

the division is based on particle universes (level 5, last of the geometry levels), and each particle in each pebble is handled as a separate depletion zone, resulting in a total of 200 burnable materials. A geometry plot shows each fuel kernel in different color:

With

div sep 3

the division is based on the pebble universe (level 2, the third universe counted backwards from the end), and the number of depletion zones is reduced to 4, one for each pebble:

When the number of pebbles and fuel kernels per pebble increases to several thousand, this makes a huge difference for the total number of depletion zones.

The way the division works is not always very intuitive. In the example above, <lvl> = 2 results in the same division as <lvl> = 1, and <lvl> = 4 in the same divison as <lvl> = 3. Usually the best way is to try different values and look at the geometry plotter for the result (note that setting rgb values in the material cards fixes the color scheme and doesn't show the division).

## References

- ^ Leppänen, J.
*"Serpent – a Continuous-energy Monte Carlo Reactor Physics Burnup Calculation Code."*User manual, June 18, 2015.